Protect your R1200 GS
Headlight Protector with Quick Release Fastener for LED Headlight BMW R 1200 GS from 2013/ BMW R1200GS Adventure from 2014
Our headlight protector has been thoroughly tried and tested over the years weve sold thousands.
Even the biggest stones wont be able to damage your headlight with this!
New durable stainless steel model now available with quick release fastener! Now you can clip on the headlight protector and detach it again as needed. Just bolt the sturdy and secure side struts. And of course the protector comes with everything you need to fit it. This headlight protector has been developed for off-road use and is not street legal.
Heat Protection Shield Front Manifolds for BMW R 1200 GS from 2013/BMW R1200GS Adventure from 2014
Due to the position of the R 1200 GS boxer engine, unlike on other motorbikes, the manifolds are far over to the outside, completely free and exposed. Travelling over rough and smooth, there is always a risk of scratching a manifold on something or getting stuck. The consequences - dents, scratches or, in the worst case scenario, holes. We have the solution: the heat protection shield by Touratech provides optimum protection for the manifold. A useful and inexpensive accessory that usually pays for itself the first time its used. This heat shield is made from laser-cut stainless steel. The design blends perfectly with the overall look of the new R 1200 GS. Very simple, fast and secure mounting.
Stainless Steel Crash Bar, BMW R 1200 GS from 2013
No matter which way the GS should fall, the Touratech crash bar is right where it is needed. The most comprehensive all-round protection there has ever been for a boxer engine! A cage of 25-mm strong, 2-mm thick stainless steel tubes completely encloses the cylinders. Any forces that occur are safely deflected and distributed to gently break them down. Numerous assembly points, intended bending points and the central strut guarantee safe protection not only of the cylinders, but also of the frame and engine of your R 1200 GS. Despite the impressive tube diameter, the crash bar is positioned as closely as possible to the vehicle and has no effect at all on the leaning angles or ground clearance. Made exclusively of strong, electropolished stainless steel, the crash bar will not rust. Even deep scratches are less frightening, and can simply be ground off. The assembly points are perfectly matched to the R1200GS! And needless to say, everything that is needed to fit it is included in the delivery.
Stainless Steel Crash Bar Extension BMW R 1200 GS from 2013
The Touratech crash bar extension protects the delicate radiator, the fairing and even the tank of the new water boxer! Even though BMW has fitted the radiator as closely as possible to the R1200GS , its bottom corners still protrude quite a lot. A bad drop can be all it takes to put paid to a trip - and you can expect a large bill for repairs. The Touratech crash bar extension will put an end to annoying scratches on the fairing! Made exclusively of strong, electropolished stainless steel, the extension will not rust. Even deep scratches are less frightening, and can simply be ground off. Fitting the crash bar extension onto the Touratech engine guard or the original BMW engine guard is simple and straightforward.
ABS sensor protection, front for BMW R1200GS from 2013/BMW R1200GS Adventure from 2014
ABS cannot function without information about the wheel speed. Proper protection for the sensitive wheel speed sensors is therefore essential, especially on machines that often travel on rough ground.
The shapely guard made of stainless steel protects the front ABS sensor from coarse dirt and stones.
Brake Calliper Cover (Set) Front for BMW R 1200 GS from 2013/BMW R1200GS Adventure from 2014
Just a few years ago, an elegant cover over the callipers was included in the standard fittings on many motorbikes when they left the factory. Unfortunately, though, all searches for this protective and attractive cover for the R 1200G S have proved futile. And yet it not only hides the often ugly individual components of the brake, but also stops the aggressive brake dust from settling on the rims and protects the brakes against rain and salt water, pebbles and dirt. Our covers are made of PU, come as an easy-to-fit set, and make sure that the front brake system of your GS looks good - a beautiful accessory elegantly covering the very technical brake calliper.
Cardan Guard for BMW R 1200 GS from 2013/ BMW R1200GS Adventure from 2014
The exposed rear axle housing is subjected to extreme loads when riding off-road. We have developed the perfect protection to prevent scratches and stone damage, as well as more serious damage, when riding over scree or other obstacles. It is made of impact-resistant, fibreglass-reinforced plastic, and wraps itself around the cardan housing like a protective hand. Needless to say, we have allowed for BMWs proposed cooling air supply, and have left a corresponding opening on the underside at the front. And furthermore, our cardan guard will also give your R 1200 GS an unmistakeable, individual look!
Cardan Crash Bung BMW R 1200 GS from 2013/ BMW R1200GS Adventure from 2014
A little item that prevents big damage!
Sadly, the cardan housing of your R 1200 GS can suffer serious scratching and other damage even if it just falls over when stationary. If such a mishap occurs off-road, scree and dirt can even damage the rear axle seal, and in the worst case leaking oil can prevent you from travelling further.
Fitting this highly resilient, beautifully shaped crash bung in time can eliminate this danger - and prevent the expensive consequences!
Engine Guard Extension *Expedition*, BMW R 1200 GS from 2013/ BMW R1200GS Adventure from 2014
We have developed an engine guard extension to go with our *Expedition* engine guard. The design is the same, technically and optically. The *Expedition* extension closes the gap between the engine guard and the rear wheel. An unbeatable advantage, especially off-road! Nothing can get stuck or caught around the main stand. This makes it much easier to slide over stones, rocks or tree stumps. The engine guard extension also protects parts of the exhaust from stones and other kinds of dirt that get thrown up. Also really useful in road use! The many angles of the 4-mm thick aluminium sheet provide maximum stability. There is no restriction of ground clearance. The *Expedition* engine guard extension attaches to the main stand in moments.
Engine Guard Expedition for BMW R 1200 GS from 2013/BMW R1200GS Adventure from 2014
In creating the BMW R 1200 GS, the developers at BMW have produced a motorbike that practically invites you take it on an off-road excursion. Our development team were able to make a number of further improvements to its positive off-road characteristics. This engine guard is an absolute revolution! Touratech have attached great importance to its robustness and functionality.
Serious damage, such as holes in the engine block, can be effectively prevented by fitting the large Touratech engine guard. Maximum strength is provided by multiple folded ridges in the 4 mm thick aluminium base plate, while an additional lower stainless steel attachment plate on the engine ensures the force of an impact is distributed over a large area via 6 bolting points. Ground clearance is not restricted by these two base plates.
Rear Brake Fluid Reservoir Guard BMW R 1200 GS from 2013/BMW R1200GS Adventure from 2014
On the BMW the brake fluid reservoir is all too easily accessible, putting it at risk of damage or tampering. Made from laser-cut aluminium, Touratechs brake fluid reservoir guard effectively prevents damage and undesired access to the reservoir lid, yet you can still easily see the fluid level. The guard simply bolts onto the existing mounting point.
Frame Guard large/small for BMW R 1200 GS from 2013/BMW R1200GS Adventure from 2014
Perfect protection for the frame of the GS - and preserves its value! Years of experience have taught us that it is essential to protect the painted frame pipes around the area of the boots. Sadly, the paint in this area is unable to cope even with the normal amount of stress that occurs when touring and wearing road boots. The frames of bikes whose riders often ride standing up, wear enduro boots or ride off-road soon become unsightly because the paint is rubbed off, leaving the unprotected frame pipes exposed to all sorts of destructive influences.
Frame Guard large:http://shop.touratech.de/01-045-5035-0
Frame Guard small:
Cylinder Protector, Aluminium, for BMW R 1200 GS from 2013
Easy to fit + lightweight + high level of protection
We accepted these challenges, and the result is a cylinder protector that meets all these criteria!
Made of 3 mm aluminium and with specific attachment points, the Touratech cylinder protector can cope with R1200GS drops as well as tougher impacts. Now theres an end to scratches - and even worse damage - to valve covers. Tested in Madagascar as well as various other locations, the protector has more than proved its abilities.
Touratech Hand Protectors GD for BMW R 1200 GS from 2013
Unlike the original ones these hand protectors are not fitted to the clamps on the control units or brake unit but directly onto the tubular handlebars. This considerably reduces the risk of the hand brake lever mounting breaking off if you fall and thus making it doubtful whether you can continue riding. The hand protector can be combined with various spoilers and then offers optimum protection against wind and weather. A very strong, sturdy construction which has proved itself time and again in many rallies and on other motor cycles.
Stainless Steel Radiator Protector, BMW R1200GS from 2014/BMW R1200GS Adventure from 2014
BMW is going to rely on water cooling in new boxer engines as well from 2013. This means that optimum performance can be combined with a long service life. With its technically perfect implementation, the system has just one weak point: the sensitive radiator.
The Touratech radiator protector shields the vulnerable lamellae of the radiator against damage and thus provides an enormous safety benefit! The dread of flying stones, sticks or other debris will be no more. A small investment will make your trip a whole lot safer!
Optically unobtrusive yet in the unmistakeable Touratech-style, the radiator protector made of laser cut, stainless steel blends in with the R 1200 GS design perfectly.